Professional heating, cooling & air quality services serving Town and Country and surrounding communities in Missouri. NATE-certified, 24/7 emergency response.
From emergency repair to planned installation, we deliver expert HVAC service across every specialty.
Heat pumps rely on a precise balance of refrigerant pressure, electrical components, and airflow to deliver efficient heating and cooling year-round. Professional repair addresses compressor hard starts, frozen coils, faulty thermostatic expansion valves, and auxiliary heat lockout conditions.
Properly sealed and insulated ductwork is essential for delivering rated BTU output to every room in your home. Our technicians repair collapsed sections, seal leaks with UL-listed mastic and mechanical fasteners, and verify balanced airflow across all supply registers after service.
A dryer that takes multiple cycles to dry clothes or feels excessively hot to the touch signals a restricted vent line. Technicians clear lint accumulation using rotary brush systems and compressed air, then verify exhaust velocity meets manufacturer specifications for safe, efficient operation.
Professional AC tune-ups follow a multi-point inspection protocol covering thermostat calibration, condensate drain clearing, electrical connection tightening, and evaporator coil cleaning. Maintaining clean coils and proper superheat readings keeps your system running at peak rated efficiency.
Upgrading to a modern heat pump delivers dual-mode heating and cooling from a single system, with top-tier models achieving 10+ HSPF and 20+ SEER2 ratings. Proper installation includes Manual J load calculations, refrigerant line sizing, and electrical panel verification for reliable year-round comfort.
Scheduling professional furnace maintenance each fall ensures your heating system delivers full BTU output without wasting fuel. Technicians inspect the inducer motor, verify pressure switch operation, calibrate gas valve output, and clean the burner assembly for reliable cold-weather performance.
Upgrading to a smart thermostat enables precise scheduling, remote access, and energy usage reporting that can reduce heating and cooling costs by 10 to 15 percent. Professional installation ensures correct wiring to your HVAC system, including C-wire verification and multi-stage equipment compatibility.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
Indoor air quality suffers when ductwork harbors years of accumulated particulate matter, allergens, and biological growth. Thorough duct cleaning addresses every branch run, main trunk line, and register boot using agitation tools and high-powered vacuum extraction to restore clean airflow.
When a mini-split displays error codes, produces weak airflow, or fails to reach setpoint, the fault often lies within the inverter board, thermistor sensors, or refrigerant circuit. Professional repair restores rated SEER output and eliminates the inefficient short cycling that drives up utility costs.
Replacing an aging HVAC system with properly sized, high-efficiency equipment can reduce energy costs by 30 to 50 percent. Professional installation covers equipment selection, ductwork modifications, refrigerant line installation, electrical upgrades, and thorough commissioning to verify rated SEER and AFUE output.
Whether you are purchasing a home, preparing for seasonal demands, or evaluating replacement options, a thorough HVAC inspection provides actionable data. Technicians measure airflow, test safety controls, assess AFUE and SEER performance, and deliver a written report with prioritized recommendations.
When your boiler produces inconsistent heat, unusual noises, or pressure fluctuations, the root cause often involves sediment buildup, failing motorized valves, or degraded seals within the hydronic loop. Experienced technicians restore system balance and verify safe operation through combustion analysis.
HVAC emergencies do not follow business hours, and a failed system in extreme temperatures puts your household at risk. Our technicians carry common replacement parts including capacitors, contactors, ignitors, and fan motors to resolve most failures in a single visit and restore comfort fast.
When your AC blows warm air, short cycles, or fails to start, the problem may involve a failed compressor, low refrigerant charge, frozen evaporator coil, or faulty control board. Professional repair identifies the exact fault and restores rated SEER efficiency through precise, manufacturer-guided procedures.
Town and Country property owners know that HVAC emergencies do not wait for business hours. A failed furnace in January risks frozen pipes, and a dead air conditioner in August creates dangerous indoor heat. With 11,618 residents depending on reliable climate control, KIC Refrigeration provides 24/7 emergency HVAC service built to respond fast and fix the problem right the first time.
Rapid dispatch, accurate diagnostics, and fully stocked service vehicles are not optional in Town and Country — they are essential. Our MO technicians evaluate every emergency call with system age, warranty status, and repair-versus-replace economics in mind, recommending the solution that makes the most financial sense for your situation. That honest approach saves Town and Country property owners money.
The certifications, standards, and commitments that set our HVAC service apart.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
Every technician on our team holds current NATE certification — the highest standard in the HVAC industry for installation and service competency. You get a technician who has passed rigorous exams on system diagnostics, refrigerant handling, and equipment commissioning.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
Get the information you need to make confident HVAC decisions for your property.
HVAC repair costs in Town and Country typically range from $150 to $500 for minor fixes such as capacitor replacement, contactor swaps, or thermostat wiring issues. Mid-range repairs like blower motor replacement or refrigerant recharging run $500 to $1,200. Major repairs — including compressor replacement, heat exchanger repair, or evaporator coil swap — cost $1,200 to $2,500 or more depending on equipment brand and system type. The final price depends on whether you have a furnace, heat pump, air conditioner, boiler, or ductless mini split, as parts and labor vary significantly between system types. Our NATE-certified technicians diagnose the issue accurately on the first visit, and KIC Refrigeration provides a written estimate with transparent pricing before any work begins. We never charge a diagnostic fee when you proceed with the recommended repair.
Most HVAC installations, major equipment replacements, and significant ductwork modifications in Town and Country require a mechanical permit from the local building department. This applies to furnace and air conditioner replacements, heat pump installations, boiler swaps, and new ductless mini split systems. Minor repairs like part replacements and refrigerant recharges typically do not require permits. KIC Refrigeration handles all permitting, code compliance documentation, and scheduling of final inspections on your behalf — you do not need to visit any government office or coordinate with inspectors. Permits exist to ensure your system is installed safely and to code, which protects your home and preserves your equipment warranty. Unpermitted work can create liability issues and complicate future home sales. We ensure every project meets current Missouri mechanical codes and International Mechanical Code standards.
Yes. KIC Refrigeration provides around-the-clock emergency heating and cooling repair throughout Town and Country and surrounding Missouri communities. Whether your furnace fails during a cold snap and pipes are at risk of freezing, your air conditioner dies during a dangerous heat wave, or you detect the smell of gas near your equipment, our technicians respond quickly. Every service vehicle carries common replacement parts — capacitors, contactors, ignitors, blower motors, control boards, and refrigerant — so most emergency repairs are completed in a single visit. We do not charge extra trip fees for after-hours calls, and our dispatchers are trained to triage situations over the phone so the right technician arrives with the right equipment. Call us anytime and we will have a crew on the way.
As a guideline for Town and Country homeowners, consider replacement when your system is 15 to 20 years old, when the repair cost exceeds 50 percent of a new system, when the equipment uses R-22 refrigerant which is no longer manufactured and costs $100 or more per pound, or when your system runs constantly without adequately heating or cooling your home. Additional indicators include frequent breakdowns — more than two per heating or cooling season — rising utility bills despite regular maintenance, uneven temperatures between rooms, and excessive noise or dust. The age thresholds vary by equipment type: air conditioners and heat pumps typically last 15 to 20 years, furnaces 20 to 25 years, and boilers 25 to 30 years. KIC Refrigeration provides honest repair-versus-replace assessments at every service call, including side-by-side cost projections for both options.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most Missouri locations. For Town and Country homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
Most residential HVAC installations in Town and Country, MO are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
Our reputation is built on honest service, skilled technicians, and systems that perform.
"Our mini split stopped cooling mid-summer and they fit us in the next morning. Diagnosed a bad capacitor, replaced it on the spot. Back to normal in under an hour."
"KIC Refrigeration repaired our heat pump when two other companies said it needed full replacement. Saved us thousands. Still running great six months later."
"KIC Refrigeration handled our emergency furnace repair during a cold snap. They prioritized us because we have elderly parents in the home. Truly caring people."
Our NATE-certified crews provide HVAC service throughout the surrounding area.